adminLearn how to change the battery in your key fob with our step-by-step guide. Locate, open, remove, insert, and close with ease. Keep your key fob working properly.If you own a 2020 Silverado, you may eventually find yourself in need of replacing the battery in your key fob. While this task may seem daunting at first, it’s actually quite simple with the right guidance. In this blog post, we will walk you through the step-by-step process of changing the battery in your 2020 Silverado key fob. We will start by showing you how to locate the battery compartment, then move on to opening the key fob and removing the old battery. After that, we will guide you through the process of inserting the new battery and closing the key fob. By the end of this post, you will be equipped with the knowledge and confidence to tackle this task on your own, saving you time and money in the process. So let’s dive in and take the first step towards a fully functioning key fob for your Silverado.
Locating the Battery Compartment
When it comes to changing the battery in your 2020 Silverado key fob, the first step is locating the battery compartment. In order to do this, you will need to find the small slot on the side of the key fob. This slot is where you can insert a flathead screwdriver or a coin to pry open the key fob and access the battery compartment.
Once you have located the slot, insert the tool and gently twist to pop the key fob open. Be careful not to use too much force, as you could damage the key fob or injure yourself. Once the key fob is open, you will be able to see the battery compartment, which is typically located on one side of the fob.
If you are having trouble locating the battery compartment, refer to the owner’s manual for your 2020 Silverado. The manual should have detailed instructions and diagrams to help you find and access the battery compartment with ease.
Opening the Key Fob
When it comes to changing the battery in your 2020 Silverado key fob, the first step is opening the key fob. This can be a bit tricky, but with the right tools and technique, it can be done. Firstly, you will need a small flathead screwdriver to carefully pry open the key fob. Start by inserting the screwdriver into the seam between the two halves of the key fob. Gently apply pressure and work your way around the edges until the two halves start to separate. Be sure to go slowly and be gentle to avoid damaging the key fob.
Once you have the two halves of the key fob separated, you will see the inside components of the key fob, including the old battery. Take note of the orientation of the old battery and make sure to remember how it was positioned before removing it. This will make it easier to insert the new battery in the correct orientation.
After successfully opening the key fob and removing the old battery, you are one step closer to replacing the battery and getting your key fob working like new again.
Removing the Old Battery
When it comes time to replace the battery in your 2020 Silverado key fob, it’s important to do so carefully and correctly to avoid damaging the fob. One of the first steps in the process is removing the old battery. To do this, you will need a small flathead screwdriver or a coin to open the key fob.
Once you have the necessary tool, you can use it to gently pry open the key fob. Start by locating the seam along the edge of the fob, and then insert the screwdriver or coin into the seam. Carefully twist the tool to separate the two halves of the fob, being mindful not to force it and damage the fob.
After you have successfully opened the key fob, you will need to locate the old battery. In most key fobs, the battery is located underneath the circuit board. You may need to use the screwdriver again to carefully lift the circuit board and access the old battery.
Inserting the New Battery
After successfully removing the old battery from your 2020 Silverado key fob, it’s time to insert the new battery. Ensure that you have the correct replacement battery for your key fob, usually a CR2032 3V lithium coin cell battery. Before inserting the new battery, take a moment to clean the inside of the battery compartment with a dry cloth to remove any dust or debris that may have accumulated.
Once the compartment is clean, carefully place the new battery into the designated slot, making sure that the positive side is facing upwards. Press down gently to secure the battery in place. Take a moment to double-check that the battery is properly seated and secured within the compartment to avoid any issues with connectivity once the key fob is reassembled.
With the new battery securely in place, you can now proceed to reassemble the key fob by following the steps in the next subheading, Closing the Key Fob. Your 2020 Silverado key fob should now be ready for use with its new battery properly inserted and functioning.
Closing the Key Fob
After successfully inserting the new battery into your 2020 Silverado key fob, it’s time to close the key fob and secure the new battery in place. Carefully place the back cover of the key fob over the battery compartment, making sure it aligns with the rest of the fob. Apply gentle pressure to the cover to ensure it snaps securely back into place.
Once the back cover is in position, press down firmly on all sides of the key fob to make sure it is completely closed. Check that there are no gaps or loose areas, as these could indicate that the cover has not been properly secured. Ensuring a tight closure will help to protect the new battery and prevent it from dislodging during use.
With the key fob fully closed, test all the buttons to ensure they are functioning properly. If everything is in working order, your 2020 Silverado key fob is now ready to use with its new battery. You can rest assured that you’ve successfully completed the battery replacement process and that your key fob is ready for secure and reliable performance.
Frequently Asked Questions
What tools do I need to change the battery in a 2020 Silverado key fob?
You will need a small flathead screwdriver and a replacement CR2032 battery.
Where is the battery located in the 2020 Silverado key fob?
To access the battery, you will need to carefully pry open the key fob using the small flathead screwdriver.
What type of battery does the 2020 Silverado key fob use?
The 2020 Silverado key fob uses a CR2032 3V lithium coin cell battery.
How do I remove the old battery from the 2020 Silverado key fob?
Once the key fob is open, you can easily lift out the old battery and replace it with the new one.
Can I replace the battery in my 2020 Silverado key fob myself?
Yes, replacing the battery in the key fob is a simple and quick process that you can do yourself.
Where can I purchase a replacement battery for my 2020 Silverado key fob?
You can find replacement CR2032 batteries at most hardware stores, electronics stores, or online retailers.
How do I reassemble the 2020 Silverado key fob after replacing the battery?
Simply place the new battery in the compartment and carefully snap the key fob back together until it clicks into place.
Add comment